JUNIOR AND SENIOR
K3 STANDARD EQUIPMENT
CHASSIS
- 1.25″ (32mm) & 1.125 (28mm) multi-alloy construction
- 41.25″ wheelbase
- Gloss black powdercoat
- 10° KPI, 15° caster, adjustable
- Adjustable ackerman
- Adjustable front ride height
- Heat-treated billet 17mm spindles
- 40mm rear axle with 2 bearings
- Billet aluminum rear hubs
- KG ‘Ignite’ steering wheel
- 2 position steering hub
- 4 quart fuel tank with integral pick-up & vent
ENGINE SPECS AND ACCESSORIES
- Briggs Racing LO206 Factory Sealed Engine
- 206cc Air-cooled 4-cycle
- Pull Start
- Walbro Carb
- 6100 RPM electronic rev limiter
- approximately 9 BHP
- 2 pc billet aluminum engine mount, 8 degree inclination
- Hilliard Flame Clutch w/mounting bolt kit
- EK #35 pitch chain, 40″ length
- 2 pc #35 rear sprocket, red anodize finish
- Chain guard w/mounting hardware
- RLV #5507 LO206 exhaust header
- RLV #4104 exhaust silencer
- RLV #4144 exhaust clamp
- Exhaust header wrap-4′
- Exhaust silencer/header support bracket
- Briggs LO206 exhaust gasket
- Briggs LO206 header mount hardware
- Briggs 555729 spec air filter
- Fuel line & filter
- Crankcase pulse fitting
- Vent tube kit
- Catch can kit
BODY WORK
BRAKES
- MCP 2 piston caliper – ‘no shim’ gap adjustment
- MCP master cylinder
- 200mm ‘Wave’ rotor
- Braided stainless brake lines
SEAT
- G-Seat
- Fixed lower mounts
- Bolt-on adjustable upper mounts
WHEELS
- DWT Alumilite, black anodized
- Direct spindle mount front wheels
AVAILABLE OPTIONS
CADET
K2 STANDARD EQUIPMENT
CHASSIS
- Fully adjustable pedal platform assembly
- 1.125 (28mm) multi-alloy construction
- 40.00″ wheelbase
- Gloss black powdercoat
- 10° KPI, 15° caster, adjustable
- Adjustable ackerman
- Adjustable front ride height
- Heat-treated billet 17mm spindles
- 30mm rear axle with 2 bearings
- Adjustable wheel base
- Billet aluminum rear hubs
- KG ‘Ignite’ steering wheel
- 2 position steering hub
- 3.5L fuel tank with integral pick-up & vent
ENGINE SPECS AND ACCESSORIES
- Briggs Racing LO206 Factory Sealed Engine
- 206cc Air-cooled 4-cycle
- Pull Start
- Walbro Carb
- 6100 RPM electronic rev limiter
- approximately 9 BHP
- Includes red carburetor slide
- 2 pc billet aluminum engine mount, 8 degree inclination
- Hilliard Flame Clutch w/mounting bolt kit
- EK #35 pitch chain, 40″ length
- 2 pc #35 rear sprocket, red anodize finish
- Chain guard w/mounting hardware
- RLV #5507 LO206 exhaust header
- RLV #4104 exhaust silencer
- RLV #4144 exhaust clamp
- exhaust header wrap-4′
- Exhaust silencer/header support bracket
- Briggs LO206 exhaust gasket
- Briggs LO206 header mount hardware
- Briggs 555729 spec air filter
- Fuel line & filter
- Crankcase pulse fitting
- Vent tube kit
- Catch can kit
BODY WORK
BRAKES
- MCP 2 piston caliper – ‘no shim’ gap adjustment
- MCP master cylinder
- 6″ diameter, slotted rotor
- Braided stainless brake lines
SEAT
- G-Seat
- Adjustable lower mounts
- Bolt-on adjustable upper mounts
WHEELS
- DWT Alumilite, black anodized
- Direct spindle mount front wheels
AVAILABLE OPTIONS
Rental Restrictions
** Currently there are no Margay Ignite 206 go kart available to rent**
Requirements for renting a Margay Ignite 206 go kart at BMP:
-72 second or better lap time in our rental karts.
-Jeans and closed toed shoes required if you don’t have a race suit/shoes.
-Helmet, neck brace, and race jacket are required, but can be rented from
us for $10 each if you don’t own them.
-Gloves are required but not provided.
-Helmet, neck brace, and race jacket are required, but can be rented from
us for $10 each if you don’t own them.
-Gloves are required but not provided.
Equipment
All racers must have helmet, gloves, race suit or equivalent, and children must have an approved chest protector.